The Goodman® SSZ14 14 SEER Heat Pump uses the environmentally friendly refrigerant R-410A and features operating sound levels that are among the best in the heating and cooling industry. R-410A is chlorine-free to help prevent damage to the ozone layer. With its 14 SEER rating, the SSZ14 will help reduce energy consumption throughout the life of the system.
Standard Features:
- R-410A chlorine-free refrigerant
- High-efficiency scroll compressor
- High-density foam compressor sound blanket
- SmartShift™ technology to ensure quiet, reliable defrost
- Factory-installed bi-flow liquid-line filter dryer
- Factory-installed suction-line accumulator
- Compressor short-cycle protection
- 850 RPM condenser fan motor
- Factory-installed compressor crankcase heater
- Factory-installed high-capacity muffler
- High- and low-pressure switches
- Service valves with sweat connections and easy access to gauge ports
- Copper tube/enhanced aluminum fin coil
- Fully charged for 15’ of tubing length
- Contactor with lug connection
- Ground lug connection
- AHRI Certified; ETL Listed
Cabinet Features:
- Goodman® brand sound control top design
- Steel louver coil guard
- Heavy-gauge galvanized-steel cabinet
- Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval
- Top and side compressor and tubing access
- Service ports and controls are accessible while unit is operating
- When properly anchored, meets the 2001 Florida Building Code unit integrity requirements for hurricane-type winds. (Anchor bracket kits available.)
CAPF, CAUF, CHPF and CSCF Dual Refrigerant Series Cased, Painted Upflow/Downflow, Horizontal/Vertical “A” Coils
Goodman® coils are designed for use with Goodman® Brand Gas Furnaces, Split System Air Conditioners and Heat Pumps, as well as modular, two-piece blowers. Each cased coil has a quality, galvanized-steel cabinet.
Standard Features:
- Suitable for use with R-410A and R-22 refrigerants
- Rust-proof, thermoplastic drain pans feature a low water-retention design
- Check flowrater expansion device for heat pump or cooling-only applications
- Rifled copper tubing and louvered aluminum fin coils on CAPF, CAUF, and CSCF coils
- Rifled aluminum tubing and louvered aluminum fin coils on the CHPF coil
Cabinet Features:
- Foil-face insulation
- Galvanized leather-grain finish
- Architectural Gray paint finish on CAPF and CHPF cased coils
- Split-seam front for easy access
- 17½”, 21”, and 24½” CHPF coils have one 3½” adapter plate
- 17½”, 21”, and 24½” CAPF coils have two 1¾” adapter plates
The Goodman® GMVC95 Two-Stage, Variable-Speed Gas Furnace features a patented aluminized-steel tubular heat exchanger and energy-efficient Hot Surface Ignition system. This furnace is run-tested for heating or combination heating/cooling applications. Goodman’s GMVC95 high efficiency gas furnace with two-stage heating and a variable-speed circulating blower provides efficient and economical performance. The 95% AFUE GMVC95 qualifies for the new 2011 $200 energy tax credit.
Standard Features:
- Dual-diameter tubular heat exchanger
- Two-stage gas valve operates with two-stage or singlestage thermostats
- ComfortNet™ Communications System compatible
- Efficient and quiet variable-speed ECM circulator motor gently ramps up or down according to heating or cooling demand
- 120V Silicon Nitride igniter designed for long igniter life
- Furnace control board with self-diagnostics, color-coded low-voltage terminals, and provisions for electronic air cleaner and 120-volt or 24-volt humidifiers
- Low constant fan allows homeowner to activate very low speed to efficiently circulate air throughout the home. This setting costs as little as a 100-watt light bulb to operate.
- Dual-certified for sealed combustion direct vent (2-pipe) or non-direct vent (1-pipe) applications
- Quiet two-speed induced draft blower
- All models comply with California NOx emissions standards
Cabinet Features:
- Fully insulated, heavy-gauge steel cabinet with durable baked-enamel finish
- Foil-faced insulation lines the heat exchanger
- Easy-to-install top venting is standard; alternate flue/vent connections on some models
- Designed for multi-position installation – GMVC95: upflow, horizontal left or right; GCVC95/9: downflow, horizontal left or right
- Airtight solid bottom for side return applications and easy-cut tabs for effortless removal in bottom air inlet applications
- Convenient left or right connection for gas/electric service
- Coil and furnace fit flush for most installations
|
